electronic

One Watt LED Night Light

This is a very simple electronic project. I built this as a night light in my sleeping room.

The reason for building this was, the existing LED night light that I bought from the Mr DIY is a bit dangerous because it needs to be connected to AC power source and my daughter always wants to play with it.

With this LED night light, I can connect it to any mobile phone’s power bank that has a USB port. And it is safe to play with. It doesn’t get hot even it ran for hours!

Bill of materials:

A one watt LED (RM0.20)- bought it from the China website.
A heat sink for LED (RM0.20)- bought it from the China website.
A 39 ohm 1 watt resistor (RM0.10) – bought it from an electronic shop at Jalan Pasar, Pudu
A LM317 voltage regulator (RM1.50) – bought it from an electronic shop at Jalan Pasar, Pudu
A heat sink for LM317 (RM1.00) – bought it from an electronic shop at Jalan Pasar, Pudu
A Mamee instant noodle cup – recycle
A broken iPad USB cable – recycle
Some card board – recycle

Total cost is less than RM4!

1. First, you will need to solder all the component together. You can refer to the circuit suggested in this website: http://www.instructables.com/id/Super-simple-high-power-LED-driver/

2. Make a few card boards that cut into the instant noodle cup shape. Make a hole at the middle of one of the card board and put the LED into the middle.

3. Pull other electronic components to the back. Put a layer of white paper at the side of LED for better effect. Pull back the electronic components and screw the heat sink and the LM317 together with the card board.

4. Use glue (any) to stick the card board to the instant noodle cup and it’s all done.

5. I run some test with the watt meter. It’s working at 0.9 to 1w which is within my expectation!

I can bring this light to any where because it is portable and safe. Including toilet! if I don’t want to have a very bright light at the mid night when visiting toilet.

So. What’s next? Maybe a solar panel with rechargeable battery to power this little thing? Stay tuned!

Thanks for reading!

Electronics Project – Simple Card Read Keyboard Emulator Using Arduino Pro Micro

I bought this little thing – Micro Pro – from the China website. I think it is a clone or compatible to the SparkFun’s Micro Pro. It is easy to use. It comes with USB that you can use it to program the microcontroller or let the microcontroller to communicate with your computer. You can simply useÂ the Keyboard library from the Arduino to program a keyboard emulator: http://www.arduino.cc/en/Reference/KeyboardPrintln.

Below is the specification of the microcontroller:

ATmega32U4 running at 5V/16MHz
Supported under Arduino IDE v1.0.1
On-Board micro-USB connector for programming
4 x 10-bit ADC pins
12 x Digital I/Os (5 are PWM capable)
Rx and Tx Hardware Serial Connections

Below is the source code for my program that emulates a card reader keyboard:

int button = 2;

void setup() {
  pinMode(button, INPUT_PULLUP); // Use internal pull up resistor
  Keyboard.begin();
}

void loop() {
  int pressed = digitalRead(button) == 0;
  if (pressed) delay(500);
  if (pressed && digitalRead(button) == 0) {
    Keyboard.println("111111");
    delay(2000);
  } else if (pressed) {
    Keyboard.println("222222");
    delay(2000);
  }
}

If you press the button once quickly, the microcontroller will send the card data string “111111” (with new line) to your PC via USB HID keyboard driver.

If you press the button once a little bit longer (around 500 milliseconds), the microcontroller will send the card data string “222222” (with new line)Â to your PC via USB HID keyboard driver.

I’m using a internal pull up resistor in the microcontroller itself so that I do not need to have a external resistor to pull up or down the floating digital pin (when used as input). When the input pin is pull down (when the switch is pressed) to the ground, the digitalRead will return zero value and otherwise it will be value one.

It’s so simple that you can make your program ready within minutes. Of course, you must first make sure the programming environment (IDE, the COM port of the Micro Pro is properly installed) is ready.

One Watt LED Night Light

Electronics Project – Simple Card Read Keyboard Emulator Using Arduino Pro Micro

Recent

Search

Recent

Search

Tags